pantry makeover

We all have our own dirty little secrets in our home… the ones just hidden out of sight. From the crazy closet to the horrible garage, we wince a little every time that door opens. Ours was the pantry. Our literal skeleton in the closet, and we pretty much had everything in the pantry… minus the skeletons.

Sometimes we keep those sore spots because let’s be honest: They’re working for us right now and we don’t have time to change them.

There’s no shame in that, right?

Okay, maybe we did let it get a little out of hand. Such is life.

Our pantry makeover was our desperate attempt to change something. Our non existent system had gotten out of control, and we were ready for something simplified and different.

In retrospect, who knew the new system we have going would make grocery shopping so much easier?

Like a breath of fresh air in the menu planning department, we’re even amazed by how much smoother our meal prep rituals for the family can run.

Not too long ago with the previous albatross of a pantry, we’d just guess at what to buy, because figuring out what we did and didn’t have with the old system was like searching for that lego piece your 5 year old had sucked up in the vacuum cleaner.

Ain’t nobody got time for that.

And most of the time we pretend we didn’t see that obscure piece that was sucked up into said vacuum cleaner. It’s one less casualty to the foot at night.

So we gutted it…….

And spackled it……

And began building it back, new.

It may seem like a complicated build on the surface, but it’s easier than one might think. Today, we’re breaking it down.

That, and there’s always the added benefit of demo day- making up for years of suppressed resentment over wire shelves, lost items, and that fabulous grease magnet known as matte builder’s beige.

Tearing things apart is kind of fun.

So here’s a little how to, and the supplies you will need in an easy pantry makeover:

• 3/4 inch thick melamine board • 2 x 2 x 8 pine boards • 1 x 3 x 8 pine boards (primed) • 1 x 2 x 8 pine boards (primed) • wood glue • #6 2 1/2 inch wood screws • finish nails • L brackets • caulk • quart of paint to match melamine board

helpful hint: how much of each of these supplies will depend on the size of your pantry or shelving space.

What we used:
• (10) 3/4(thick) x 15 3/4(w) x 96 inch (l) melamine board • (3) 2 x2 x 8 pine boards •(10) 1 x 3 x 6 pine boards (primed) •(14) 1 x 2 x 8 pine boards (primed) • box of 100 count #6 2 1/2 inch wood screws • large bottle of wood glue • RYOBI 16 gauge nailer • RYOBI drill • RYOBI impact driver • scroll saw • L brackets • caulk • quart of paint to match melamine board – minimal painting!

First things first: We patched the holes and painted the the pantry, then began installing our wall braces. To install the wall braces, you’ll need to find the studs in your wall(s) and mark their location. Then decide on the height and number of shelves you will use and mark their placements on your wall(s). I suggest marking where you want the bottom of the shelf to hit.

Next, measure the length of your wall(s) and cut your 1 x 2’s to that length. If you are installing on two walls that will meet, remember that you will need to compensate for the width of the 1 x 2 butting up against the other 1 x 2 from the second wall.

You’ll want a brace on any wall that touches the shelf.

Once you have your measurements, cut the braces to the correct length. Then spread some wood glue on the side touching the wall, and line up the top edge with the markings you made earlier. Level the brace and shoot or hammer a couple of nails into it to hold it in place.

Next, pre-drill two holes into the brace where the studs are, and screw in your 2 1/2 inch screws. (Repeat this for all your braces.)

Once your braces are up, measure and cut your melamine board to size. We ran one shelf the length of the shorter wall, and then butted the longer wall’s shelf board to it.

You can brace the front side of the shelf in several ways. We used a combination of a center support between the two shelves, and then on the long wall, a dividing shelf.

To make a center support between the two shelves, notch out a 2 x 2 x 8 so that each shelf will rest on the notch. We notched it so that 3/4 of it’s thickness was uncut because we planned to finish off the shelves with a 1 x 3 on the front. This would give us the finished look we were after.

We took a melamine board, and laid it on each brace. We held the 2 x 2 up to it, made everything level, and marked where we needed to notch.

Using a scroll saw, we notched out a place for each shelf to rest. (You’ll need to notch out two sides.) We also cut our 2 x 2 to 3 1/2 inches above the bottom of the last notch, so that when we ran our 1 x 3 it would be flush.

We painted the 2 x 2, and when it was dry we ran a bead of glue on the top of the wall braces, and placed all the melamine boards in place.

Helpful Hint: We found a mallet helpful for hammering some of the shelves in.

Then we put some glue on the notches, and slid the 2 x 2 into place.

Once it’s dry, you can begin adding cubbies and a half wall. We added a half wall to provide a great place to store our trash can and vacuum. It also added a little extra support to that side.

When cutting your melamine board for the cubbie dividers, remember to notch out the back top where it will hit the support. Then simply attach it with some plastic “L” brackets you can buy in the same area as the melamine board. (If your cut is precise, you can get away with hot gluing them in place and then caulking it.)

We really loved the whole “vintage cubbie” look, and the polished finish the front ledge gave our pantry, so we decided to add this final step. You’ll want to measure a the 1 x 3 to finish off the front. Cut it to size, then glue and nail it.

We finished off the edges close to the walls with some primed pine 1 x 2’s cut to size, and simply glued and nailed them into place.

Finally, caulk all the holes and edges or any gaps. Paint the caulk as well as any exposed edges to match the melamine board.

Pat yourself on the back, because you are now the proud owner of a new pantry!

You can read all about our sources here, but we polished off the front with these simple labels from DLawless

And crowned it of with this fun flee market find…

and the great warm natural light given off by this omnidirectional cree bulb we picked up at Home Depot. It’s kind of amazing what it did for us to pull down that ‘boob light’ {as we so affectionately refer to them}.

We are loving the new feel and functionality of the space, and as always we’d love to see if you try it! Let us know if you have any questions. It’s amazing what a little elbow grease can do for the functionality {and sanity} in your home.

Have an inspired day!

::This post was brought to you in partnership with Cree who compensated us for our time and provided us with the bulb. Please read our full disclosure pertaining to partnerships and construction here. Please follow all directions on packaging.::